Skip to content
  • Home
  • Shop
  • F.A.Q?
  • Advantages Downrod System
  • Support
  • Outriggers
  • Mounting Methods
  • Photos & Videos
  • Transducer Downrods
  • Transducer Mounting Solutions
  • Warranty
Menu
  • Home
  • Shop
  • F.A.Q?
  • Advantages Downrod System
  • Support
  • Outriggers
  • Mounting Methods
  • Photos & Videos
  • Transducer Downrods
  • Transducer Mounting Solutions
  • Warranty
Search
Close
$0.00 0 Cart

Downrod for Humminbird Mega Live Transducers

Home / Uncategorized / Transducers / Humminbird / Downrod for Humminbird Mega Live Transducers

Downrod system for transom and trolling motor mounted side view and down view humminbird transducers.

  • Description
  • Reviews (0)

Downrod for Humminbird Mega Live transducer.

NOTE:  MEGA LIVE ICE does not require this downrod.  You need only a downrod cone to place on your existing ICE Downrod:  http://www.fishingspecialties.com/product/downrod-cone-for-humminbird-mega-live-ice/

This downrod is 48 inches long and is large enough to allow the transducer cables to pass through the downrod.  This helps to protect the cables when in use and eases cable management as there is nothing for the cable to wrap about when scanning with the downrod.

The downrod ships with a strain relief ring to protect the cable as it exits the top of the downrod.

There is a single mounting methods for the Humminbird Mega Live:  A post end for connection of the well made Humminbird bracket.  Post ends neck the downrod back to trolling motor shaft diameter so you can easily connect the Humminbird bracket.  There is a wire channel in the upper portion of the post end to allow the cable to run through the downrod.  A C clip is provided to prevent the cable from touching the raw end of the downrod as it enters the tube.

There are also two handle options:

  1.  A solid 12 inch long handle.
  2.  A telescoping 12 to 18 inch long handle.

And finally extension tubes are available for use with very deep boats.  Typically extension tubes are mounted at the top of the downrod and serve the function of allowing the handle to be raised higher and thus be a bit more accessible.

To determine proper downrod length, use the following illustration:

Determine Downrod Length
In the illustration above, the downrod will extend about 20 inches above the baseplate.  The users feet are below the gunnel by about 4 inches in a Skeeter boat.  So there is 24 inches above the deck to attach the handle which rises 9 inches so the top of the handle will be 33 inches above the deck (about the height of a countertop).

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Humminbird Mega Live downrod system

Choose product options

$164.00

Downrod Type and Length 1 Downrod Type and Length

Downrod End for Transducer Connection 2 Downrod End for Transducer Connection

Downrod Handle 3 Downrod Handle

Handle for turning and aiming the transducer

Extension for top of Downrods 4 Extension for top of Downrods

Extensions raise the top of downrods for the installation of handles or to make it easier to grasp and bring into the boat. Telescoping downrods extend only 4 inches above a baseplate.

    Related products

    • Bowducer on trolling motor deck

      Sea Ark Boat, Trolling Motor Deck Mount

      SeaArk Select options
    • Cisco MTU90

      Lund Mounting – 90 degree Sport Track (Cisco Bracket)

      Mounting onto Boat $69.00 Add to cart

    You may also like…

    • Downrod Storage Straps

      Velcro Storage Straps for all Downrods

      Downrod Storage Options $8.95 Add to cart
    • Downrod storage clips

      Downrod Storage Clips for 1.5 inch tube

      Downrod Storage Options $9.95 Add to cart
    Copyright © 2023 Fishing Specialties Inc - All Rights Reserved. - patents pending on several products
    • Outriggers
    • Transducer Mounting Solutions